Autor Thema: Decoder programing  (Gelesen 1733 mal)

Offline Juan Carlos

  • Junior-Mitglied
  • Beiträge: 10
Decoder programing
« am: 01. Juli 2018, 04:13:17 »
Can windigipet program a markilng msd3 decoder? Can it download sounds from the marklin website?
Thank you
Juan Carlos
  • Win-Digipet-Version:
    2015 small version

Offline Thomas Hirsch

  • Senior-Mitglied
  • Beiträge: 1454
  • Ort: NRW-Krefeld Ort bei GoogleMaps suchen
Re: Decoder programing
« Antwort #1 am: 01. Juli 2018, 11:44:26 »
Hello Juan Carlos,

yes it is possible to programm Märklin Mld and Msd Decoders with the WDP-Programmer, but it depends also on your Digital Center .

To change Decoders in MFX Mode you need a Märklin Central-Station 2 or 3 .
Also possible is it with "CC-Schnitte" from Can-Digital-Bahn!

changing the Soundfiles is only possible with the Märklin Decder-Programmer 60971 an the MDT Programm !

Loading sounds from the Märklin Homepage and bringing them to your Decoder  only possible with  MDT Software!

Changing Soudfiles need always a special Programmer from the Decoder manufacturer!
Mit freundlichen Grüßen

  Thomas Hirsch

________________________

System :Märklin Motorola + Mfx / Centrale Fahren: Tams Mastercontrol  über RS 232 / Booster 6017 /  /CC-Schnitte für MFX Programmierung und  Magnetartikel / HSI mit 28 S88/  Intel DUAL Core 2x2500 Mhz , 2048 MB Ram  XP-prof SP III / Gleis: Märklin M- , und K-Gleis / Decoder : 6090x und MFX ,Mld,Msd &  Lopi4 / Uhlenbrock freie Zone / WD Premium Ed 2018
  • Win-Digipet-Version:
    WD 2021.b
  • Anlagenkonfiguration:
    Tams Mastercontrol  über RS 232 / Booster 6017 /  CC-Schnitte zur mfx prgrammierung und Magnetartikel / HSI mit 23 S88
  • Rechnerkonfiguration:
    PC - Intel DUAL Core 2x2500 Mhz / XP-prof.

Offline Juan Carlos

  • Junior-Mitglied
  • Beiträge: 10
Re: Decoder programing
« Antwort #2 am: 01. Juli 2018, 17:36:44 »
Hello Thomas, thank you for your response.
I have a Marklin central station but it is not the 2 or 3.
From your answer I get that it would not work for programming. Is that right?
Thank you
Juan Carlos
  • Win-Digipet-Version:
    2015 small version

Offline Thomas Hirsch

  • Senior-Mitglied
  • Beiträge: 1454
  • Ort: NRW-Krefeld Ort bei GoogleMaps suchen
Re: Decoder programing
« Antwort #3 am: 01. Juli 2018, 22:39:26 »
Hello Juan Carlos,

It should work with the normal Cv`s for V-max / min , acceleration decerleration etc. ,but not for changing the soundfiles!

If it does not work under MFX it would be possible under MM2!
Mit freundlichen Grüßen

  Thomas Hirsch

________________________

System :Märklin Motorola + Mfx / Centrale Fahren: Tams Mastercontrol  über RS 232 / Booster 6017 /  /CC-Schnitte für MFX Programmierung und  Magnetartikel / HSI mit 28 S88/  Intel DUAL Core 2x2500 Mhz , 2048 MB Ram  XP-prof SP III / Gleis: Märklin M- , und K-Gleis / Decoder : 6090x und MFX ,Mld,Msd &  Lopi4 / Uhlenbrock freie Zone / WD Premium Ed 2018
  • Win-Digipet-Version:
    WD 2021.b
  • Anlagenkonfiguration:
    Tams Mastercontrol  über RS 232 / Booster 6017 /  CC-Schnitte zur mfx prgrammierung und Magnetartikel / HSI mit 23 S88
  • Rechnerkonfiguration:
    PC - Intel DUAL Core 2x2500 Mhz / XP-prof.

Offline Juan Carlos

  • Junior-Mitglied
  • Beiträge: 10
Re: Decoder programing
« Antwort #4 am: 01. Juli 2018, 23:01:52 »
Hello Thomas,
Thank you again for your response.

Juan Carlos
  • Win-Digipet-Version:
    2015 small version