Hi ,
I have very often a lost connection of the CS2 , and that create a lot off failure on the network.
Could you help! PC XP SP3, CS2 60214, soft 1.4.0, hard 4.33 , WDP 11.3.162 french. ethernet 100mbs.
I have no idee about this trouble, just restart the connection , and all continue, if there are'nt accident.
Thanks in forward
Best regard.
André
??? Bonsoir Andrè, I'm not the expert with CS2 & WDP French version or otherwise. But an intermitant connection loss must firstly point to a possible L.A.N. Patch Cable connection fault. Are the connectors both ends in good condition ? Are you using a HUB to interface between your CS2 and laptop, if so, the HUB may be your problem. Have you tried a cross wire RED patch cable without using a HUB ?
Best Regards - Dave CONNER
??? I forgot to ask you if the cmd ping works from WINDOWS when your connection problem with the CS2 surfaces ?
Best Regards - Dave CONNER
Thanks Dave,
The connection is direct between PC and CS2 , cable of 5 meter and cross connexion.
The PC itself didn't gave information about the lost of connexion.
I have just to reactive the cs2 (extra- status digital..), I don't have to do any action of type of network.
Regards
André
Additional info:
Cable exchanged, no info into the events, cards status the counter still increasing, on CS2 both light still on.
regards
André :(
Hello André,
what do you mean by "no info into the events"?
What message is showed by Win-Digipet when the message gets lost?
Regards
Markus
Hi Markus,
No info into events = windows didn't detecd any trouble.
Message from windigipet french nearly = lost of connection with CS2 reinit them.
Regards
André
Hi André,
maybe you try if an update of the CS2 to 1.5.2 will help.
Regards
Markus
Thanks Markus,
The current version of CS2 is 1.4.0, where did you found 1.5.2?
Regards
André
Hello André,
the 1.5.2. is avaiable via Online Update not via USB update version.
Regards
Markus
Thanks, I'll test it.
Reagrads
André
Hello Markus,
I had to modifier the internet network, windigipet was running without external internet. The CS2 is now at 1.5.2 I wait few days before conclude.
Thanks again
Regards
André
Hi Markus
I lost several days because the site WDP wasn't accessible.
The upgrade of the CS2 didn't solve the trouble. I include message in french how said:
"CS2 didn't answer reinit digital system"
To simplifie messages I go to the english version with the last update.
Regards
André
Hello André,
Have you tried unplugging the ethernet cable on the CS2 and plugging it back in? This helped
me a few times when I had the same message.
Elliott
Hi Elliot
I have tested several actions, when the lost of connection become, the ethernet is still actif!
Regards
André
Hi Andre,
Have you now tryed the english 2009.4b?
Regards
Markus
Yes Markup,
but it's too early to conclude.
Hi Markus,
Since the last update, the trouble changed. Now as several train should run, one of them didn't start because theh start command wasn't done. Here are 4 panels, it never start and the control didn't get the alarm after delay was out. In that case the trouble is inside of wdp.
I think that situation is not easy to be determined, the came several time in a hours.
Hi Andre,
are you sure you used the correct contact numbers in the profile. The first contact number for starting the train in the profile is number 86. But the route is named 111>98? Which number is correct 111 or 86? Can you check this.
Regards
Markus
You are right, sorry
After have made a change on that train I forgot to delete the not used itinery.
Today the system was connected for more than 4 hours, without trouble.
This incident is to be closed
NB I notice that I edit any profile the Wdpupdu2.exe take 98% of load and need two minutes before give back the control to the main program.
Thanks and best rerards
André
Andrè, can you check the output of your CS power supply. Perhaps that is what is giving you problems ?
Best Regards. Dave CONNER
Sorry, I did not see that this problem was closed. Dave CONNER